Fuse Termiticide Insecticide
Fuse Termiticide / Insecticide
Fuse Termiticide / Insecticide
Fuse Termiticide / Insecticide contains the two active ingredients imidacloprid and fipronil
Fuse Termiticide / Insecticide Features:
* Labeled for termite and perimeter pest control applications
* Contains 2 active ingredients: imidacloprid and fipronil
* Offers structural termite protection
Fuse Termiticide / Insecticide Uses/Applications:
Application as a Termiticide: Fuse may be used in and along the outside perimeter of structures and building construction to prevent and control termite infestations.
Use Instructions: For subterranean termite control, specific treatment recommendations may differ due to regulations, treatment procedures, soil types, construction practices and other factors. The purpose of chemical soil treatment for termite control is to establish a continuous treated zone (horizontal and/or vertical) between the wood and other cellulose material in the structure and the termite colonies in the soil Follow all federal, state, and local regulations and treatment standards for protection of a structure from termites. The establishment of an aerial or above ground colony may require additional treatments to control the termites, as well as landscape modifications, and/or structural repairs to deny termites of a moisture source. Use a 0.067% to 0.13% dilution based on current recommendations. For a typical control situation, a 0.067% diluation is used. A 0.13% dilution may be used when a severe or persistent infestation exists.
When treating adjacent to an existing structure, the applicator must check the area to be treated, and immediately adjacent areas of the structure, for visible and accessible cracks and holes to prevent any leaks or significant exposures to persons occupying the structure. People present or residing in the structure during application must be advised to remove their pets and themselves from the structure if they see any signs of leakage. After application, the applicator is required to check for leaks. All leaks resulting in the deposition of termiticide in locations other than those prescribed on this label must be cleaned up prior to leaving the application site. Do not allow people or pets to contact contaminated areas or to reoccupy contaminated areas of the structure until the clean-up is completed.
Structures that contain wells or cisterns within the foundation of the structure can only be treated using the treated backfill method described in the treatment around wells and cisterns section of the label. Consult state and local specifications for recommended distances of wells from treated area, or if such regulations do not exist, refer to Federal Housing Administration Specifications (H.U.D) for guidance.
Foam Application Use Directions: Mix appropriate concentration of FUSE™ in water and add the manufacturer's recommended quantity of foam agent to the FUSE™ solution (see table for foaming recommendations). Apply a sufficient volume of FUSE™ foam alone or in combination with liquid solution to provide a continuous treated zone at the labeled rate for specific application sites.
Depending on the circumstances, foam applications may be used alone or in combination with liquid solution applications. Applications may be made behind veneers, piers, chimney bases, into rubble foundations, into block voids or structural voids, wall voids, under slabs, stoops, porches, or to the soil in crawlspaces, and other similar voids.
Mixing Instructions: For perimeter pest treatments mix a 0.067% to 0.13% spray dilution of Fuse by filling the treatment tank ¼ to ½ full with water, then add the 0.3 to 0.6 fluid ounces Fuse per finished gallon. The filling hose must be equipped with an anti-backflow device or the water flow must include an air gap to protect against back siphoning. Add the remaining water to the tank while agitating.
Retreatment: Retreatment for subterranean termites can only be performed if there is clear evidence of reinfestation or disruption of the treated zone due to construction, excavation, or landscaping and/or evidence of the breakdown of the treated zone in the soil. The vulnerable or reinfested areas may be retreated in accordance with application techniques described in this product's labeling. The timing and type of these retreatments will vary, depending on factors such as termite pressure, soil types, soil conditions and other factors which may reduce the effectiveness of the treated zone. Retreatment may be made as either a spot or complete treatment.
Fuse Termiticide / Insecticide Target Pests:
Use to kill and to provide residual control of the following pests: Ants (acrobat, Argentine, big-headed, Caribbean crazy, carpenter, crazy, odorous, pavement, and thief), Asian lady beetles, darkling beetles, Cellar spiders, Box-elder bugs, pill bugs, Cluster flies, European earwigs, House crickets, Millipedes, and Silverfish.
Fuse Termiticide / Insecticide Active Ingredients:
States Registered: AL, AZ, AR, CO, CT, DC, DE, FL, GA, HI, ID, IL, IN, IA, KS, KY, LA, ME, MD, MA, MI, MN, MS, MO, MT, NE, NV, NH, NJ, NM, NC, ND, OH, OK, OR, PA, RI, SC, SD, TN, TX, UT, VT, VA, WA, WI, WV, WY
Fuse Termiticide / Insecticide EPA Reg. No. 53883-328
Fuse Termiticide / Insecticide Size: 27.5 fl oz bottle
Fuse Termiticide / Insecticide Class: Neonicotinoid, Pyrazole
Fuse Termiticide / Insecticide Category: Insecticide
Fuse Termiticide / Insecticide Manufacturer: Control Solutions, Inc.